C-110-M1St2D Media Converter, Perle Systems, Mfr#: 05041840

Maximum frame size of 2048 bytes

1

Internal

Fast Ethernet

10/100Base-T, 100Base-BX-D

Multi-mode

Yes

10/100 Media Converter Module Unmanaged

Twisted Pair, Optical Fiber

5.29 oz

Transceiver/Media Converter

1.24 Mile

2

1

1550 nm, 1310 nm

Yes

50/125 µm, 100/140 µm, 85/125 µm, 62.5/125 µm

5% to 90% non-condensing

This green LED is operational only when power is applied. The LED is on ; when the 10/100Base-TX link is operatinal in full duplex mode. The LED ; is off when in half duplex.

FCC Part 15 Class A, EN55022 Class A

5% to 95% non-condensing

0 C to 50 C (32 F to 122 F)

Full (Default); Half

1024 MAC Addresses

512 Kbits frame buffer memory

7.2

This green LED is operational only when power is applied. The LED is on ; when the speed of the copper Ethernet port is running at 100 MBPS. The ; LED is off when in 10 MBPS

This green LED is operational only when power is applied. The LED is on ; when the 100Base-TX link is on and flashes with a 50% duty cycle when ; data is received.

This green LED is operational only when power is applied. The LED is on ; when the 100Base-FX link is operatinal in full duplex mode. The LED is ; off when in half duplex.

EN 60825-1:2007

Captive thumb screws enable fast insertion and removal. Can be further ; tighten with a screwdriver.

Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITU-T 625)

UL 60950-1

32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ; ground and power

The media converter can perform a loopback on the 100Base-X fiber ; interface; Disabled (Default - Up); Enabled- The ; 100Base-X receiver is looped to the 100Base-X transmitter. The ; 100Base-TX transmitter is taken off the interface.

100 (Default); 10

If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP ; Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation ; (802.3u) is disabled the Media converter will use the RX Energy method ; on the 100Base-TX interface to set the port MDI or MDIX whichever is ; appropriate; Enabled (Default)- ; Either a straight-through or crossover type cable can be used to connect ; the media converter to the device on the other end of the cable; Disabled- If the ; partner device on the other end of the cable does not have the Auto-MDIX ; feature a specific cable, either a straight-through or crossover will be ; required to ensure that the media converter's transmitter and the ; partner devices transmitter are connected to the others receiver. The ; Media converter's 100Base-TX port is configured as MDI-X with this ; switch setting.

2.1

RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable

1.5kv

Enabled (Default)- ; The media converter uses 802.3u Auto-negotiation on the 100Base-TX ; interface. It is set to advertise full duplex; Disabled- The media ; converter sets the port according to the position of the speed and ; duplex switches.

Full (Default); Half

This green LED is operational only when power is applied. The LED is on ; when the 100Base-FX link is on and flashes with a 50% duty cycle when ; data is received.

This green LED is turned on when power is applied to the media ; converter. Otherwise it is off. The LED will blink when in Loopback test ; mode.

Enabled (Default)- ; When the state of the receiver is changed on the 100Base-TX interface it ; is reflected on the 100Base-FX fiber transmitter. When the state of the ; receiver on the 100Base-FX interface is changed it is reflected on the ; 100Base-TX transmitter; When a Far-End Fault Indication is received on the fiber interface the ; 100Base-TX transmitter is turned off. When the Far-End Fault Indication ; is cleared the transmitter is turned back on; Disabled- The ; 100Base-TX and the 100Base-FX fiber interface operate independently. ; Far-End Fault indication on the 100Base-FX fiber interface has no effect ; on the 100Base-TX interface.

EN55024

minimum range of -25 C to 70 C (-13 F to 158 F)

Up to 3,048 meters (10,000 feet)

Canada

1