| Property | Value |
|---|---|
| Electrical Safety | UL 60950-1 |
| Operating Altitude | Up to 3,048 meters (10,000 feet) |
| Immunity | EN55024 |
| Power / TST | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode. |
| Storage Humidity | 5% to 95% non-condensing |
| Storage temperature | minimum range of -25Β° C to 70Β° C (-13Β° F to 158Β° F) |
| Emissions | FCC Part 15 Class A, EN55022 Class A |
| Remote Loopback #2 | The media converter can perform a loopback on the link #2 fiber interface; Disabled (Default - Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #1's fiber transmitter is taken off the interface. |
| Fiber link 2 on / Receive activity (LK2) | This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received. |
| Remote Loopback #1 | The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default - Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #2's fiber transmitter is taken off the interface. |
| Bit Error Rate (BER) | u003c10-12 |
| Heat Output ( BTU/HR ) | 8.53 |
| Card insertion and removal | Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver. |
| Operating Humidity | 5% to 90% non-condensing |
| Fiber link 1 / Receive activity (LK1) | This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received. |
| Auto-Negotiation | Auto (default up)- Fiber Negotiation is performed for both fiber ports. Full and half duplex will be advertised. Pause will advertise support for Symmetrical and Asymmetrical Pause. Pause frame will not be acted upon or generated but will be passed through; Off- Negotiation on both fiber ports will be disabled. Settings of Link mode and Fiber fault alert will be determined by those switch settings. Pause frames will not be acted upon or generated but will continue to be passed through. |
| 1000Base-X | Multimode dual SC to single mode single SC fiber connector model; Available in SC, ST and LC connector models |
| Fiber Fault Alert | Enabled - (default up)- If the media converter detects a loss of fiber signal on a fiber receiver, it will immediately disable its fiber transmitter signal. This, in effect, notifies the remote fiber link partner that an error condition exists on the fiber connection. The setting of this switch applies to both fiber ports; Disabled: The media converter will not monitor for fiber fault or generate them; Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #2's fiber transmitter is taken off the interface. |
| Edge Connecter | 32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power |
| Laser Safety | EN 60825-1:2007 |
| Maximum Power Consumption ( Watts ) | 2.5 |
| Operating temperature | 0Β° C to 50Β° C (32Β° F to 122Β° F) |
| Configuration Mode Strap | Auto (default) enable management module to overwrite hardware switch settings Switch - Use on-board DIP switches |
| Country of Origin (subject to change) | Canada |
| Package Quantity | 1 |
Cm-1000Mms1Sc80U Media Convert, Perle Systems, Mfr#: 05062400
$3646.99
Free shipping will be applied on orders over $50
CM-1000MM-S1SC80U - Managed Gigabit Fiber to Fiber Converter Module: 1000BASE-SX 850nm multimode (SC) [550 m/1804 ft.] to 1000BASE-BX 1510nm TX / 1590nm RX single strand fiber, single mode (SC) [80 km/50 miles]. Managed or unmanaged operation.
9999 in stock
Subtotal:
$3646.99
You must be logged in to post a review.
Reviews
There are no reviews yet.