| Item | Electronic Pressure Sensor |
| Range | 0 to 5800 psi |
| Analog Output | 4 to 20mA or 0 to 10V DC |
| Control Output | PNP |
| On/Off Setting | Programmable |
| Max. Pressure | 24,650 psi |
| Power Required | 18 to 30V DC |
| Process Connection | 1/4 in NPT |
| Electrical Connection | 4 Pin M12 |
| Display | 4 Digit LED |
| Operating Temp. Range | -13 Degrees to 176 Degrees F |
| IP Rating | 65/67 |
| Standards | CE, CULus |
| Housing Material | Stainless Steel |
| Wetted Materials | Stainless Steel |
| Application | for industrial applications |
| Characteristics deviation [% of the span] | <± 0,25 (BFSL) / <± 0,5 (LS), (Turn down 1:1, BFSL = Best Fit Straight Line, LS = limit value setting) |
| MTTF [years] | 129 |
| Max. voltage drop switching output DC [V] | 2 |
| Short-circuit protection | yes |
| IO-Link functions (acyclical) | application specific tag |
| Number of inputs and outputs | Number of digital outputs: 2, Number of analogue outputs: 1 |
| Overload protection | yes |
| Analogue end point | 80...400 bar 1160...5800 psi 8...40 MPa |
| Output signal | switching signal, analogue signal, IO-Link, (configurable) |
| Temperature coefficient zero point [% of the span / 10 K] | 0,2, (-25...80°C) |
| Min. pressure cycles | 100 million |
| Min. bursting pressure | 1700 bar 24650 psi 170 MPa |
| Delay time programmable dS, dr [s] | 0...50 |
| Number of analogue outputs | 1 |
| Max. load [?] | 500 |
| Total number of outputs | 2 |
| Set point SP | 2.5...400 bar 37...5802 psi 0.25...40 MPa, 2.5...400 bar 40...5800 psi 0.25...40 MPa |
| MAWP (for applications according to CRN) | 800 bar 11580 psi 80 MPa |
| Min. difference between SP and rP | 1.7 bar 24 psi 0.17 MPa, 2 bar 30 psi 0.2 MPa |
| Response time [ms] | < 1.5 |
| Integrated watchdog | yes |
| SIO mode | yes |
| Current consumption [mA] | < 35 |
| Long-term stability [% of the span] | <± 0,05, (Turn down 1:1, per 6 months) |
| Number of digital outputs | 2 |
| UL approval | UL Approval no. J014 |
| Max. response time analogue output [ms] | 3 |
| Tightening torque [Nm] | > 50, (depends on lubrication, seal and pressure rating) |
| Transmission type | COM2 (38,4 kBaud) |
| Restrictor element integrated | no (can be retrofitted) |
| Reset point rP | 1...398.5 bar 10...5780 psi 0.1...39.85 MPa, 0.9...398.4 bar 13...5778 psi 0.09...39.84 MPa |
| Communication interface | IO-Link |
| Connection | Connector: 1 x M12, coding: A, Contacts: gold-plated |
| Repeatability [% of the span] | <± 0,1, (with temperature fluctuations < 10 K, Turn down 1:1) |
| Power-on delay time [s] | 0.3 |
| Damping process value dAP [s] | 0...4 |
| Shock resistance | DIN EN 60068-2-27 50 g (11 ms) |
| Measuring element | metallic thin film cell |
| Pressure rating | 800 bar 11580 psi 80 Mpa |
| Electrical design | PNP/NPN |
| Min. load resistance [?] | 2000 |
| Materials | 1.4542 (17-4 PH / 630), stainless steel (1.4404 / 316L), PBT+PC-GF30, PBT-GF20, PC |
| Protection | IP 65, IP 67 |
| Storage temperature [°C] | -40...100 |
| Min. process cycle time [ms] | 3, 2.3 |
| Media | liquids and gases |
| Reverse polarity protection | yes |
| In steps of | 0.1 bar 1 psi 0.01 MPa, 0.5 bar 10 psi 0.05 MPa |
| IO-Link resolution pressure [bar] | 0.1, 0.2 |
| EMC | DIN EN 61000-6-2 DIN EN 61000-6-3 |
| Analogue start point | 0...320 bar 0...4640 psi 0...32 MPa |
| Permanent current rating of switching output DC [mA] | 250 |
| Min. insulation resistance [M?] | 100, (500 V DC) |
| Temperature coefficient span [% of the span / 10 K] | 0,2, (-25...80°C) |
| Special feature | Gold-plated contacts |
| Output function | normally open / normally closed, (parameterisable) |
| Hysteresis deviation [% of the span] | <± 0,1, (Turn down 1:1) |
| IO-Link process data (cyclical) | function bit length pressure 16 device status 4 binary switching information 2, function bit length pressure 14 binary switching information 2 |
| IO-Link revision | 1.1 |
| Measuring range | 0...400 bar 0...5800 psi 0...40 MPa |
| Type of pressure | relative pressure |
| Switch point accuracy [% of the span] | <± 0,4, (Turn down 1:1) |
| Analogue current output [mA] | 4...20, (scalable 1:5) |
| Switching frequency DC [Hz] | < 500 |
| Operating voltage [V] | 18...30 DC, (to SELV/PELV) |
| Profiles | Smart Sensor ED2: Digital Measuring Sensor (0x000A), Identification and Diagnosis (0x4000), Smart Sensor: Process Data Variable, Device Identification, Device Diagnosis |
| Required master port type | A, (when pin 2 not connected: B) |
| Ambient temperature [°C] | -25...80 |
| Analogue voltage output [V] | 0...10, (scalable 1:5) |
| Vibration resistance | DIN EN 60068-2-6 20 g (10...2000 Hz) |
| Medium temperature [°C] | -25...80 |
| Type of short-circuit protection | pulsed |
| Damping for the analogue output dAA [s] | 0...4 |
| Vacuum resistance [mbar] | -1000 |
| Pressure Equipment Directive | Sound engineering practice, can be used for group 2 fluids, group 1 fluids on request |
| Protection class | III |
| SDCI standard | IEC 61131-9 |
| Parameter setting options | hysteresis / window, normally open / normally closed, switch-on/switch-off delay, Damping, Display unit, current/voltage output |
| Materials (wetted parts) | 1.4542 (17-4 PH / 630) |
| Country of Origin (subject to change) | Germany |
| Package Quantity | 1 |
Electronic Pressure Sensor, 24,650 psi, IFM, Mfr# PN2270
$445,99
Free shipping will be applied on orders over $50
Electronic Pressure Sensor, Range 0 to 5800 psi, Analog Output 4 to 20mA or 0 to 10V DC, Control Output PNP, Programmable On/Off Setting, Power Required 18 to 30V DC, Process Connection 1/4 in NPT, Electrical Connection 4 Pin M12, Display 4 Digit LED, Wetted Materials Stainless Steel, Housing Material Stainless Steel, Operating Temp. Range -13 Degrees to 176 Degrees F, IP Rating 65/67, Max. Pressure 24,650 psi, Standards CE, CULus
Out of stock
You must be logged in to post a review.
Reviews
There are no reviews yet.