S-100-S1Sc40D Media Converter, Perle Systems, Mfr#: 05050304

3.1 in

1 in

4.7 in

10.58 oz

1

24.85 Mile

100Base-BX, 10/100Base-TX

Transceiver/Media Converter

Yes

2

Yes

S-100-S1SC40D Fast Ethernet Stand-Alone Media Converter, US Power Cord

1

S-100-S1SC40D Fast Ethernet Stand-Alone Media Converter

Rack-mountable, External, Wall Mountable, Rail-mountable

UL 60950-1

2.0 watts

167 mA

0 C to 50 C (32 F to 122 F)

100-240v AC, regulated DC adapter included

This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.

Single mode single SC Media Converters; Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITu-T 625)

Up to 3,048 meters (10,000 feet)

FCC Part 15 Class B*, EN55022 Class B*

6.8

5.5mm x 9.5mm x 2.1mm barrel socket

EN 60825-1:2007

5% to 90% non-condensing

Pause should be enabled when all devices connected to the media converter support pause. Auto-Negotiation must be Enabled to use this feature; Enabled (Default)- The Media converter will advertise Pause capability during Auto-Negotiation on the 100Base-TX interface; Disabled- The Media converter will advertise that it does not have Pause capability during Auto-Negotiation on the 100Base-TX interface.

120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches

If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate; Enabled (Default)- Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable; Disabled- If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media convertor's transmitter and the partner devices transmitter are connected to the others receiver. The Media Convertor's 100Base-TX port is configured as MDI with this switch setting.

This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received.

EN55024

6 - 30 vDC, unregulated ( 12 vDC Nominal )

5% to 95% non-condensing

RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable

Enabled (Default)- The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex; Disabled- The media converter sets the 100Base-TX port to full duplex.

u003c10-12

Enabled (Default)- When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter; When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on; Disabled- The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface.

1.5kv

minimum range of -25 C to 70 C (-13 F to 158 F)

This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received.

The media converter can perform a loopback on the 100Base-X fiber interface; Disabled (Default - Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.

Canada

1