Smi-110-S2Lc80 Media Converter, Perle Systems, Mfr#: 05071014

Maximum frame size of 2048 bytes

Full (Default); Half

minimum range of -25 C to 70 C (-13 F to 158 F)

Up to 3,048 meters (10,000 feet)

5% to 95% non-condensing

10/100/1000Base-T - RJ45; Auto- MDI/MDIX

Single mode dual LC Media Converters; Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITU-T 625)

Green - 1000 Mbps link; Yellow - 100 Mbps link; Off - 10 Mbps or no Link

100-240v AC, regulated DC adapter included

175 x 145 x 23 mm

1024 MAC Addresses

If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate; Enabled (Default)- Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable; Disabled- If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.

RS232 Serial RJ45 - Cisco pinout for use with standard CAT5

This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received.

0 C to 50 C (32 F to 122 F)

UL 60950-1

FCC Part 15 Class B**, EN55022 Class B**

Recessed pinhole button resets module

512 Kbits frame buffer memory

RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable; Magnetic Isolation - 1.5kv

Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data

Red alarm indicator activated when an alert event occurs

Enabled (Default)- The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex; Disabled- The media converter sets the port according to the position of the speed and duplex switches.

5% to 90% non-condensing

4.1watts

This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is operatinal in full duplex mode. The LED is off when in half duplex.

5.5mm x 9.5mm x 2.1mm barrel socket

( 12 vDC Nominal )

Enabled (Default)- When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter; When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on; Disabled- The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface.

This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received.

Blinking green during startup cycle; Steady green: module has power and is ready; Red : error

This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.

0.34amps at 12vdc

100 (Default); 10

EN 60825-1:2007

This green LED is operational only when power is applied. The LED is on when the speed of the copper Ethernet port is running at 100 MBPS. The LED is off when in 10 MBPS

The media converter can perform a loopback on the 100Base-X fiber interface; Disabled (Default - Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.

14

EN55024

Full (Default); Half

This green LED is operational only when power is applied. The LED is on when the 10/100Base-TX link is operatinal in full duplex mode. The LED is off when in half duplex.

Canada

1